Subway Tile Calculator
Subway tiles, the classic 3 by 6 inch rectangles borrowed from early underground stations, remain one of the most popular choices for kitchen splashbacks and bathroom walls. The tricky part of any tiling project is not laying the tiles, it is ordering the right number: too few and the job stalls mid-wall, too many and money sits in unopened boxes. The Subway Tile Calculator settles the question from three measurements: wall length, wall height, and the waste percentage you allow for cuts and breakage.
The maths is reassuringly concrete. A standard subway tile measures 3 inches by 6 inches, which is half a foot by a quarter of a foot, giving each tile a face area of exactly 0.125 square feet. Divide your wall area by 0.125 and you have the tile count before waste; add your waste allowance, round up to whole tiles, and then convert to boxes of 40 tiles, the pack size this calculator uses.
This guide explains each step of that calculation, how to choose a sensible waste percentage for your layout, and how to plan cuts, patterns, and spares like an experienced tiler. Two worked examples, a full bathroom wall and a compact splashback-sized area, show the complete arithmetic.
How the Tile Count Is Worked Out
Everything begins with the wall area: length multiplied by height, both in feet. A wall 10 feet long and 8 feet high has an area of 80 square feet. If your wall has a window, a door, or a large fitted unit, measure that obstruction separately and subtract its area later, or simply tile-count the full wall and treat the difference as extra spare tiles, which is rarely a bad outcome.
Next comes the tile itself. Six inches is half a foot and three inches is a quarter of a foot, so one subway tile covers 0.5 times 0.25 = 0.125 square feet of wall. That means exactly eight tiles cover one square foot, ignoring the thin grout lines, a detail the waste allowance comfortably absorbs. Dividing the wall area by 0.125, or equivalently multiplying by 8, gives the base tile count.
Waste is then applied as a percentage on top of that base count, and the total is rounded up, because tiles are sold whole. Finally, the tile count is divided by 40, the number of tiles in the box size used here, and rounded up again to give whole boxes. Rounding up at both stages is deliberate: it is the difference between finishing the wall and making an emergency trip for one more box from a possibly different batch.
Choosing a Waste Percentage
Waste is not carelessness; it is the honest cost of fitting a grid of rectangles to a real wall. Tiles are cut at edges, around sockets and pipes, and at corners, and the offcuts are often too small or the wrong shape to reuse. A few tiles also crack during cutting or arrive chipped, and a sensible order anticipates all of this instead of pretending it will not happen.
For a simple rectangular wall in the classic running bond pattern, 10 percent is the standard allowance and the figure used in the examples here. Straight stacked layouts with few obstacles can sometimes manage with a little less, while herringbone and other diagonal patterns waste far more, typically 15 to 20 percent, because nearly every edge tile is cut at an angle and the offcuts rarely fit anywhere.
Rooms with many cut-outs, alcoves, or plumbing penetrations deserve the higher end of the range regardless of pattern. When in doubt, round the waste up: leftover tiles from the same batch are valuable spares for future repairs, while a shortage can mean a new box in a slightly different shade, a mismatch tiler's call dye lot variation, and one that catches the eye forever.
How to Use the Subway Tile Calculator
Measure the wall in feet, decide your waste percentage from the pattern and the number of obstacles, and let the calculator do the counting.
- Measure the full length of the wall you are tiling, in feet, and enter it as the wall length.
- Measure from the worktop or floor to the top of the tiled area, in feet, and enter it as the wall height.
- Enter a waste percentage: around 10 for a simple running bond layout, 15 to 20 for herringbone or obstacle-heavy walls.
- Click Calculate to see the wall area, the number of tiles needed, and the number of boxes to buy.
- If your supplier sells a different box size, divide the tile count by that number and round up to check your order.
Measure twice and include every surface: the returns at the sides of a window reveal and the strip above a door are classic forgotten areas that eat into your spare allowance.
Worked Example 1: A Bathroom Wall 10 Feet by 8 Feet
A bathroom wall is 10 feet long and will be tiled to a height of 8 feet, in running bond, with a 10 percent waste allowance.
Step 1: Find the wall area: 10 multiplied by 8 equals 80 square feet.
Step 2: Find the base tile count: 80 divided by 0.125 equals 640 tiles, which is 80 times the 8 tiles that cover each square foot.
Step 3: Add the waste allowance: 640 times 1.10 equals 704 tiles exactly, so no further rounding is needed at this stage.
Step 4: Convert to boxes: 704 divided by 40 equals 17.6 boxes.
Step 5: Round up to whole boxes: 18 boxes must be bought.
The calculator reports a wall area of 80 square feet, 704 tiles needed, and 18 boxes. The 18th box is mostly spare tiles, which is exactly the insurance a tiler wants against a cracked tile in year three.
Worked Example 2: A Splashback 6 Feet by 4 Feet
A kitchen splashback zone measures 6 feet long by 4 feet high, also with a 10 percent waste allowance for cuts around sockets.
Step 1: Find the wall area: 6 multiplied by 4 equals 24 square feet.
Step 2: Find the base tile count: 24 divided by 0.125 equals 192 tiles.
Step 3: Add the waste allowance: 192 times 1.10 equals 211.2 tiles.
Step 4: Round up to whole tiles: 212 tiles are needed.
Step 5: Convert to boxes: 212 divided by 40 equals 5.3, which rounds up to 6 boxes.
The calculator reports a wall area of 24 square feet, 212 tiles needed, and 6 boxes. Note how the round-ups accumulate on small jobs: the smaller the project, the larger the proportion of the order that ends up as cutting allowance and spares.
Patterns Change Everything Except the Area
The wall area and the base tile count do not care about your pattern; eight tiles cover a square foot whether they are stacked in a grid, offset in running bond, or woven into herringbone. What the pattern changes is the waste. Running bond needs cuts mainly at the edges, stacked layouts need the fewest cuts of all, and herringbone consumes extra tiles at every boundary because the zigzag edge cannot follow a straight wall line.
Pattern also changes the visual size of the wall. Running bond stretches a room horizontally, a vertical stack makes a low ceiling feel taller, and herringbone adds movement that suits larger, plainer walls. Choose the pattern for the room first, then set the waste percentage to match it, not the other way round.
Grout colour is the final pattern decision, and it interacts with tile count not at all, which is precisely why it gets forgotten until the end. Decide it before ordering, because a contrasting grout shows every cut edge and lippage, while a matching grout forgives small imperfections in a way that can rescue an ambitious layout.
Planning Cuts, Batches, and Spares
Professional tilers plan the layout from the centre of the wall outward, so the cut tiles at each end are equal and reasonably wide. A layout that ends with a sliver cut of a few millimetres looks like a mistake and is fragile in practice. When your measurements suggest a sliver, shifting the starting point by half a tile usually fixes it, at the cost of a few extra cuts that your waste allowance should already cover.
Buy all your boxes at once, from the same batch or dye lot, and check the batch code on every box before you start. Tiles are manufactured in runs, and colour and even size can drift slightly between runs. The calculator's round-up to whole boxes gives you a small buffer; spending it on same-batch spares is the wisest use of it.
Keep the leftover tiles, labelled, somewhere dry. A cracked tile in five years' time is a ten-minute repair if a matching spare exists and a full re-tile discussion if it does not. Few home-improvement bargains are as one-sided as the box of spares you almost returned.
Tips for Ordering Subway Tiles
A little planning before you order saves the two classic tiling headaches: running short, and boxes that do not match.
- Measure the wall, then measure it again. Use feet consistently, include side returns and strips above openings, and write the numbers down; memory is the least reliable measuring tool on any project.
- Set waste by pattern, not by optimism. Ten percent suits simple running bond on a plain wall. Herringbone, diagonal layouts, and walls full of sockets deserve 15 to 20 percent.
- Always round up to whole boxes. Tiles and boxes are sold whole. The calculator already rounds up at both stages, so order the box figure it gives you, not the raw tile figure divided down.
- Buy one batch, in one order. Check batch codes match across boxes. A later top-up box can differ in shade just enough to be permanently visible.
- Plan the layout before the first cut. Start from the centre so edge cuts are balanced, and avoid layouts that end in sliver cuts, which look wrong and chip easily.
- Keep the spares. Labelled leftover tiles from the same batch turn a future cracked tile into a quick repair instead of a matching nightmare.
Frequently Asked Questions
1. How many subway tiles cover one square foot?
Eight. A 3 by 6 inch tile covers 0.125 square feet, and 1 divided by 0.125 is 8.
That figure ignores grout gaps, which is one reason the waste allowance exists.
2. Why does the calculator include a waste percentage?
Because cuts at edges and around obstacles, plus occasional breakages, consume tiles that never appear on the finished wall.
Ordering the exact mathematical count guarantees running short. Ten percent is the standard allowance for a straightforward layout.
3. What box size does the calculator assume?
Boxes of 40 tiles, which cover 5 square feet per box. Suppliers vary, so check the tile count of the boxes you are actually buying.
If your boxes hold a different quantity, divide the calculator's tile count by that quantity and round up.
4. Should I subtract the area of windows and doors?
You can, and for a large window it is worth doing: measure the opening and subtract its area from the wall area before entering the height and length.
Many tilers skip the subtraction on small openings and count the difference as extra spares, which is a safe and simple approach.
5. How much waste does a herringbone pattern need?
Plan on 15 to 20 percent. The angled edges mean far more cuts, and the offcuts seldom fit elsewhere in the pattern.
Herringbone also consumes more labour, so the extra tiles are rarely the largest added cost.
6. Can I use this calculator for a floor?
The arithmetic works for any flat rectangle, but floor tiles face different loads and are often larger formats.
For a floor in 3 by 6 inch tiles, use a waste figure at the higher end, since floor cuts around doorways and fixtures are frequent.
7. What if my wall measurements are in metres or inches?
Convert to feet before entering: divide inches by 12, or multiply metres by 3.281.
Mixing units between length and height is a classic error that produces a wildly wrong tile count, so convert both the same way.
8. Why round up tiles before converting to boxes?
Because you cannot lay a fraction of a tile. The usable tile count must be a whole number before it is packed into boxes.
Rounding at both stages slightly increases the order, and that small surplus is the project's insurance.
9. Do grout lines change the tile count?
Slightly. Real tiles sit a few millimetres apart, so a wall takes very slightly fewer tiles than the pure area division suggests.
The difference is small and is absorbed comfortably inside the standard waste allowance.
10. How many spare tiles should I keep after the job?
Keep at least a handful, ideally half a box, stored dry and labelled with the batch code.
Spares from the same batch are the only guaranteed colour match for a future repair.
11. What is the most common ordering mistake?
Ordering the exact base count with no waste allowance, then running short a few tiles from the end of the wall.
The second most common is mixing batches. Both are avoided by following the calculator's rounded-up box figure and buying in one order.
12. Can I tile over existing tiles?
Often yes, if the existing surface is sound, flat, and well bonded, and doing so saves removal work.
It does not change the tile count for the new layer, though it does add thickness to plan for at edges and fittings.
13. How do I handle a wall that is not a simple rectangle?
Break it into rectangles, run the calculator for each part, and add the tile counts together before converting the grand total to boxes.
Converting each part to boxes separately over-orders, because each part gets rounded up on its own.
14. What tile size is a standard subway tile?
The classic is 3 by 6 inches, the size this calculator uses, with a two-to-one length-to-height ratio.
Larger formats such as 4 by 12 inches exist and look similar, but each covers more area, so they need a different tiles-per-square-foot figure.
15. When should I order extra beyond the calculator's figure?
When the pattern is complex, the wall has many obstacles, the tiles are handmade with size variation, or the supplier cannot guarantee a matching later batch.
In those cases, raising the waste percentage in the calculator is the cleanest way to build the extra in.
CONCLUSION
Ordering tiles is a small calculation with outsized consequences, and the Subway Tile Calculator reduces it to three honest inputs: the wall's length and height, and a waste percentage chosen for your pattern rather than your optimism. The rounded-up tile and box figures it returns are designed so the wall gets finished in one go, with same-batch spares left over.
Measure carefully, set the waste for the layout you actually chose, and buy the boxes in a single order. Tile the wall once, keep the spares, and the only tiling arithmetic you will ever need to repeat is showing someone else how you worked it out.