Exterior Paint Calculator
Painting a house exterior goes wrong in predictable ways, and running out of paint two thirds of the way up the last wall is the most avoidable of them. The Exterior Paint Calculator tells you the wall area and the gallons you need before you spend anything.
Enter the total distance around your house, the wall height, and how many coats you plan to apply. You get the total exterior wall area in square feet, the paint needed for your coats, and a buying figure with ten percent added for waste, spills, and touch-ups.
The estimate uses the standard coverage of about 350 square feet per gallon for smooth exterior walls. Rough siding, bare wood, and heavy texture drink more paint, so treat the result as a sound baseline and adjust upward for thirsty surfaces.
The same arithmetic protects you at the shop counter. Paint is sold by the gallon and the five-gallon bucket, priced to tempt bulk buying, and walking in with a wall area and a gallon figure already calculated means the decision is yours, not the loudest recommendation’s. Overbuying modestly is fine; overbuying wildly wastes real money on paint that dries out in the garage.
Measuring the Distance Around Your House
The perimeter is simply the length of all the outside walls added together. For a rectangular house, measure the length and the width, add them, and double the answer. A house 40 feet long and 20 feet wide has a perimeter of 120 feet.
Walk the outside with a tape or a measuring wheel and note porches, extensions, and garage walls as you go. Sections you will not paint, such as a brick extension you are leaving alone, can be left out of the total so the estimate matches the real job.
Extensions and dormers reward care rather than cleverness. Measure each painted face where it actually is, add the runs together, and let the perimeter be the sum of real walls instead of a tidy rectangle the house only vaguely resembles. The calculator rewards honest measurement with an honest answer.
From Perimeter and Height to Wall Area
Multiplying the perimeter by the wall height unrolls the whole exterior into one flat rectangle with the same area. A 120-foot perimeter with 10-foot walls gives 1,200 square feet of wall, regardless of how the corners turn.
Wall height is measured from the ground to the eaves for each storey. Single-storey walls are commonly about 9 to 10 feet, and two-storey homes roughly double that. Gable ends, the triangles under a pitched roof, add extra area that many people handle by buying for them from the waste allowance.
Notice what the area figure does not include: it assumes walls are solid. Every opening slightly overstates the job, and every gable, chimney breast, and deep reveal slightly understates it. On ordinary houses these errors largely cancel, which is why the simple method has served estimators for generations.
How Coverage and Coats Decide the Gallons
Paint makers rate coverage at roughly 350 square feet per gallon on a smooth, sealed surface. Every coat needs that amount again, so two coats over 1,200 square feet require 2,400 square feet of coverage, which is just under seven gallons.
The ten percent waste allowance covers what stays in the tray, soaks into rollers, drips, and gets kept back for future touch-ups. Buying to the with-waste figure is cheaper than an emergency trip for one more gallon that may be mixed in a visibly different batch.
Coverage ratings come from laboratory-smooth panels, and real walls are never laboratory-smooth. The sensible response is not to distrust the figure but to hold it as the centre of a range, with the waste allowance and your own knowledge of the surface deciding which side of the range to buy.
How to Use the Exterior Paint Calculator
Two measurements and one decision are all you need: the walk around, the height, and your coat count.
- Measure the total distance around the parts of the house you will paint, in feet.
- Enter the wall height in feet, from ground level to the eaves.
- Enter the number of coats you plan to apply, usually two for a lasting exterior finish.
- Press the Calculate button to see your results instantly.
- Read the wall area, the gallons needed for your coats, and the buying figure with ten percent extra.
If different walls have different heights, work out the tallest full circuit as your baseline and rely on the waste allowance for smaller variations, or calculate each section separately and add the gallons.
Take a photograph of each wall before you measure. Later, when the ladder work starts and a question arises about which sections were included, the photographs settle it instantly and save a second round of measuring in the middle of the job.
Worked Example 1: A Single-Storey Home With Two Coats
A homeowner measures 120 feet around her single-storey house, with walls 10 feet high to the eaves. She plans two coats over the existing sound paint for a finish that will last.
- Distance around the house: 120 feet.
- Wall height: 10 feet.
- Number of coats: 2.
- Wall area = 120 multiplied by 10, which equals 1,200 square feet.
- Coverage needed = 1,200 multiplied by 2 coats, which equals 2,400 square feet.
- Paint needed = 2,400 divided by 350, which equals 6.86 gallons.
- Paint to buy = 6.86 multiplied by 1.1, which equals 7.54 gallons.
The Exterior Paint Calculator reports 1,200 square feet of wall, 6.86 gallons for the coats, and 7.54 gallons to buy. In practice she would purchase 8 gallons, keeping the opened remainder for the touch-ups every exterior eventually needs.
Worked Example 2: A Two-Storey Home With a Colour Change
A taller house measures 140 feet around with walls 20 feet high. Because the owners are changing from a dark colour to a light one, they plan a primer coat plus two finish coats, counted here as 3 coats of coverage.
- Distance around the house: 140 feet.
- Wall height: 20 feet.
- Number of coats: 3.
- Wall area = 140 multiplied by 20, which equals 2,800 square feet.
- Coverage needed = 2,800 multiplied by 3 coats, which equals 8,400 square feet.
- Paint needed = 8,400 divided by 350, which equals 24.00 gallons.
- Paint to buy = 24.00 multiplied by 1.1, which equals 26.40 gallons.
The results show 2,800 square feet of wall, 24 gallons for the coats, and 26.40 gallons to buy. Buying five-gallon buckets for most of that total cuts the cost per gallon noticeably on a job of this size.
When One Gallon Covers Less Than 350 Square Feet
The 350 figure assumes a smooth, previously painted surface in good condition. Stucco, rough timber siding, weatherboard with deep shadow lines, and bare porous surfaces can drop real coverage to 250 or even 200 square feet per gallon.
A practical adjustment is to calculate normally, then add an extra quarter to a third for very rough or very thirsty walls. Painting a test patch and measuring exactly how far one quart goes on your own siding beats any general rule.
Windows, Doors, and Whether to Subtract Them
Many estimators subtract about 21 square feet for each standard door and 15 for each window. Others skip the subtraction entirely and let those areas fund the paint that gables, trim, and extra texture will consume.
For most homes either approach lands close, because the two effects roughly cancel. If your walls are mostly glass, subtract properly. If your house has deep gables and heavy trim, leave the openings in and let them cover the extras.
Primer, Colour Changes, and Coat Planning
Bare wood, repaired render, and dramatic colour changes all benefit from a dedicated primer coat, which seals the surface so the finish coats cover evenly. Count primer as a coat in the calculator to include its volume in your buying figure.
Two finish coats remain the standard for exteriors because sunlight and weather test a single coat quickly. A job calculated honestly for primer plus two coats rarely disappoints, while a job stretched over one thin coat often needs redoing within a couple of seasons.
Estimating Trim, Doors, and the Extras
Trim drinks paint out of proportion to its area because it is fiddly, often a different finish, and usually painted in a contrasting colour bought separately. A common allowance is to price trim paint as roughly a tenth of the wall paint on a typical house, then adjust for how much timber the design carries.
Doors deserve their own small calculation: a standard exterior door with its frame takes about a fifth of a gallon for two coats. Counting doors individually keeps the extras honest instead of letting them blur into a general contingency that always seems to run out first.
Keep your measurements and results with the paint receipts, noting the colour code and the shop that mixed it. When a wall is damaged years later, that record turns a frustrating colour-matching exercise into a single quick trip.
Weather belongs in the plan alongside the gallons. Exterior paint needs dry surfaces and mild temperatures to cure properly, so the best-calculated job can still fail if it is applied ahead of rain or in scorching midday heat.
Tips for Getting the Most From the Exterior Paint Calculator
- Tip 1: Measure the real perimeter. Walk the outside of the house with a tape and add every painted section, rather than guessing from the floor plan.
- Tip 2: Use eaves height for the walls. Measure from the ground to where the wall meets the roof, and double it for a two-storey home.
- Tip 3: Plan two coats as standard. One coat rarely survives exterior weather well, so calculate for two finish coats from the start.
- Tip 4: Buy to the with-waste figure. The ten percent extra prevents a mid-job shortage and leaves paint for future touch-ups in the same batch.
- Tip 5: Adjust for rough surfaces. Stucco and bare, thirsty siding need noticeably more paint than the smooth-surface rate assumes.
- Tip 6: Count primer as a coat. If the surface is bare or the colour change is dramatic, include the primer in your coat number.
- Tip 7: Buy five-gallon buckets on big jobs. Larger containers cost less per gallon and reduce the risk of shade differences between batches.
- Tip 8: Box your paint together. Mixing all the cans of one colour together before starting evens out tiny batch differences across walls.
- Tip 9: Subtract huge openings only. A wall of glass deserves a subtraction; ordinary doors and windows conveniently offset gables and trim.
- Tip 10: Keep a labelled touch-up supply. A sealed quart from the original batch makes later repairs invisible instead of obvious.
Frequently Asked Questions
1. How much area does one gallon of exterior paint cover?
A gallon typically covers about 350 square feet on a smooth, previously painted wall.
Rough or porous surfaces can reduce that to 200 to 250 square feet per gallon.
2. Should I subtract windows and doors from the area?
For most homes it makes little difference, because the openings roughly offset gables and trim.
If your house has unusually large windows, subtracting about 15 square feet each is reasonable.
3. How many coats does an exterior need?
Two finish coats are the standard recommendation for durability and even colour.
Bare surfaces usually need a primer coat first, which you should count in your total.
4. Why does the calculator add ten percent extra?
Some paint is lost to trays, rollers, drips, and soaking into the surface.
The extra also leaves you a matching supply for future touch-ups.
5. How do I measure the perimeter of an irregular house?
Walk the outside and measure each straight section of painted wall, then add them together.
Leave out any sections you are not painting, such as a brick extension staying as it is.
6. What wall height should I enter for a two-storey house?
Measure from the ground to the eaves and enter the full height, often around 18 to 20 feet.
Alternatively, calculate each storey separately and add the paint figures together.
7. How do I allow for the triangular gable ends?
Estimate each gable as a triangle: half the base width multiplied by the height to the peak.
Many people simply let the window and door area they did not subtract cover the gables.
8. Does the surface type really change the paint needed?
Yes. Smooth painted siding follows the standard rate closely.
Stucco, rough wood, and bare render absorb far more and can need a third more paint.
9. Should primer be counted in the gallons?
Yes. Primer covers at a similar rate, so include it as one of your coats.
The calculator then prices the full job rather than only the coloured coats.
10. Can I use this for fences and sheds?
Yes. Measure the length of the fence or shed walls and their height, and treat the run as your perimeter.
Enter the coats you plan and the gallons will follow the same coverage maths.
11. What if one wall is much taller than the others?
Calculate that wall separately using its own length and height, then add its gallons to the main result.
Splitting the job into sections keeps tall gables and extensions accurate.
12. How much paint should I keep for touch-ups?
A quart to a half gallon, sealed tightly and stored away from frost, covers most repairs for years.
Label it with the colour code, the room or wall it matches, and the date it was bought.
13. Why did my last job use more paint than expected?
Common causes are rough surfaces, spraying instead of rolling, and very dry porous walls.
Spraying in particular can use a third more paint through overspray and bounce-back.
14. Is it cheaper to buy all the paint at once?
Usually yes. Larger buckets cost less per gallon, and buying together guarantees one consistent batch.
Most shops also honour returns on unopened cans, so a modest surplus is low-risk.
15. When is the best weather for using the paint?
Dry, mild days with no rain forecast for at least a day give paint time to cure properly.
Avoid painting in extreme heat, which can dry the surface before the paint bonds well.
CONCLUSION
The Exterior Paint Calculator converts two tape measurements and a coat decision into a confident shopping list: the wall area, the gallons your coats require, and a buying figure with waste already included. That is the difference between one planned trip to the shop and three frustrated ones.
Measure honestly, allow for thirsty surfaces, and buy to the with-waste number in a single batch. A well-calculated paint job starts long before the first brushstroke, and it finishes on schedule because the paint never runs out.
A house painting project succeeds on preparation long before colour touches a wall, and the estimate is the first piece of that preparation. With the area measured, the coats decided, and the gallons bought in one consistent batch, the remaining work is simply the satisfying part: watching the house change.