Gear Ratios Calculator
The Gear Ratios Calculator works out what happens when two gears mesh: how much the speed changes, and how much the turning force changes with it. Enter the teeth on the driving gear, the teeth on the driven gear and the input speed in RPM, and the tool returns the gear ratio, the output speed and the torque change. It is the quick check behind everything from bicycle drivetrains to gearboxes and workshop machinery.
Gears trade speed for torque. A small gear driving a large gear slows the output down but multiplies its twisting force, which is how a modest motor lifts a heavy load. A large gear driving a small gear does the opposite, spinning the output faster with less force behind it. The ratio of the tooth counts decides both effects exactly, and this tool makes that relationship visible in one step.
The maths rests on one firm physical fact: meshing gears must share the same tooth speed at the point of contact, so the gear with more teeth turns more slowly in exact inverse proportion to its tooth count. Because the relationship is purely proportional, the results are exact for ideal gears, and the worked examples below show every step so you can verify the figures with nothing more than division.
What the Gear Ratios Calculator Actually Measures
The gear ratio compares the driven gear with the driving gear. It is written as a number followed by : 1, and it states how many turns the input makes for each single turn of the output. A ratio of 2.00 : 1 means the driving gear spins twice for every one revolution of the driven gear, which is a reduction drive.
The output speed is the practical consequence most users want first: it tells you how fast the second shaft, wheel or spindle actually turns. The torque change completes the picture by showing the price or reward of that speed change, expressed as a percentage gain or loss relative to the input torque, before friction losses in a real machine.
Driving and Driven Gears Explained
The driving gear is the one connected to the power source, such as a motor shaft or a cyclist’s pedals. The driven gear is the one it meshes with, connected to the load, such as a wheel or a machine spindle. The order matters completely: swapping the two tooth counts in the boxes inverts the ratio and turns a reduction into an overdrive.
Tooth count, not physical diameter, is the correct input, because meshing gears share the same tooth size, so the count is exactly proportional to diameter. Counting teeth is also more reliable than measuring a worn gear with a ruler. If a gear is stamped with its tooth count, use that figure; otherwise count carefully and mark the starting tooth to avoid counting one twice.
The Formula Behind the Gear Ratios Calculator
Three short steps produce the results. First, the gear ratio equals the driven teeth divided by the driving teeth. Second, the output speed equals the input RPM multiplied by the driving teeth and divided by the driven teeth, which is the inverse of the ratio applied to speed. Third, the torque change equals the ratio minus one, multiplied by 100 to express it as a percentage.
Notice that speed and torque move in opposite directions through the same ratio. Multiply torque by the ratio and you divide speed by the ratio, which is why no gearbox can give you more of both at once. The tool states the torque change as an ideal percentage; a real gearbox loses a few percent to friction, a point covered in the limits section below.
How to Use the Gear Ratios Calculator
You need two tooth counts and one speed, all of which are usually stamped on the gears or listed in the machine manual.
- Enter the number of teeth on the driving gear, the one attached to the power source.
- Enter the number of teeth on the driven gear, the one attached to the load.
- Enter the input speed of the driving gear in revolutions per minute.
- Press the blue Calculate button and read the gear ratio, output speed and torque change.
- Use the yellow Reset button to clear the page before testing a different gear pair.
Try reversing the two tooth counts as a quick sanity check. A reduction pair should become an overdrive pair, with the output speed rising above the input and the torque change turning negative by the matching proportion.
Worked Example 1: Gear Ratios Calculator in Action
A motor pinion with 20 teeth drives a 40-tooth gear at an input speed of 1200 RPM, a classic reduction setup.
Step 1: Enter driving teeth = 20 and driven teeth = 40.
Step 2: Enter the input speed of 1200 RPM.
Step 3: Gear ratio = 40 ÷ 20 = 2.00 : 1.
Step 4: Output speed = 1200 × 20 ÷ 40 = 600.00 RPM.
Step 5: Torque change = (2.00 − 1) × 100 = +100.00%.
The result box shows a gear ratio of 2.00 : 1, an output speed of 600.00 RPM and a torque change of +100.00%. The output turns at half the input speed with double the ideal torque, exactly the trade a reduction gear is chosen for.
Worked Example 2: Gear Ratios Calculator in Action
A 36-tooth gear now drives a smaller 24-tooth gear at 3000 RPM, an overdrive setup used to spin a fan faster.
Step 1: Enter driving teeth = 36 and driven teeth = 24.
Step 2: Enter the input speed of 3000 RPM.
Step 3: Gear ratio = 24 ÷ 36 = 0.67 : 1.
Step 4: Output speed = 3000 × 36 ÷ 24 = 4500.00 RPM.
Step 5: Torque change = (0.67 − 1) × 100 = -33.33%.
The results are a gear ratio of 0.67 : 1, an output speed of 4500.00 RPM and a torque change of -33.33%. The output spins half as fast again as the input, and the negative torque change shows the force given up to buy that extra speed.
Reading the Results of the Gear Ratios Calculator Like an Expert
Read the ratio as a sentence about turns. Above 1 : 1, the input turns more than once per output turn, so you have a reduction: slower, stronger. Below 1 : 1, the output turns more than once per input turn, an overdrive: faster, weaker. Exactly 1 : 1 means equal gears passing speed and torque through unchanged, useful only for changing direction or shaft position.
Chain drives and multi-stage gearboxes multiply their stage ratios together. If one pair gives 2.00 : 1 and a second pair also gives 2.00 : 1, the combined ratio is 4.00 : 1 and the final output speed is the input divided by four. You can model each stage with this tool in turn, feeding each output speed into the next stage as its input.
Common Mistakes When Using the Gear Ratios Calculator
The most frequent error is swapping the driving and driven gears. It inverts every result, turning a planned reduction into an overdrive on paper and confusing any part ordered from the figures. Always confirm which gear sits on the power shaft before entering the counts.
A second mistake is entering gear diameters instead of tooth counts. Diameters give the same ratio only when measured perfectly at the pitch circle, which is hard on a worn gear. Tooth counts are exact and easy to verify. A third error is expecting the ideal torque figure in a real machine; friction in bearings and tooth contact always takes a small share.
Benefits and Limits of the Gear Ratios Calculator
The benefit is an instant, exact answer for the ideal gear pair, with the speed and torque consequences shown side by side. That pairing matters, because choosing a ratio on speed alone, without seeing the torque change, is how underpowered drives get built.
The limits follow from the ideal model. The tool assumes perfectly meshing gears with no slip, no backlash and no friction, and it covers a single pair of gears rather than a full multi-stage box in one step. Real output torque will be slightly lower than the ideal percentage suggests. For ratio selection, shaft speed checks and design comparisons, the figures are exactly what you need.
One more idea is worth carrying into any design decision: the ratio also predicts how a pair will behave under load changes. If the load torque doubles, a reduction pair answers with the multiplied torque it was chosen for, while an overdrive pair may stall the motor entirely, because its available torque was traded away for speed. Running the figures for the heaviest realistic load, not just the average one, is what separates a drive that works on paper from one that works every day. The calculator makes that worst-case check painless: keep the tooth counts, consider the input speed your motor holds under strain, and confirm the output torque margin still clears the load with room to spare. Machines rarely fail at their average duty; they fail at the peak nobody calculated.
Tips for Getting the Best Results from the Gear Ratios Calculator
- Count teeth, never guess. Mark the starting tooth with a pen and count around once, because a single missed tooth skews the whole ratio.
- Confirm the driver. Check which gear is on the power shaft before entering values, since swapping the pair inverts everything.
- Read the sign of torque. A negative torque change means an overdrive, so make sure the load can accept the reduced force.
- Model stages one at a time. For multi-stage boxes, feed each stage’s output speed into the next stage as its input.
- Allow for friction. Treat the torque figure as the ideal ceiling and expect a real gearbox to deliver slightly less.
- Round tooth counts never. Enter exact whole-tooth counts; the tool accepts them as typed and ratios stay exact.
- Check belt pulleys the same way. Pulley ratios follow the same inverse rule using tooth counts on toothed belts.
- Record the pair together. Note both tooth counts with the result so the setup can be rebuilt or reordered later.
Frequently Asked Questions
1. What is a gear ratio?
A gear ratio is the driven gear’s tooth count divided by the driving gear’s tooth count, written as a number to 1.
It tells you how many times the input turns for one output turn. A ratio of 3.00 : 1 means three input turns per single output turn.
2. How is output RPM calculated?
Output RPM equals the input RPM multiplied by the driving teeth and divided by the driven teeth.
So doubling the driven teeth halves the output speed. The relationship is exactly inverse, which both worked examples on this page demonstrate.
3. What does a negative torque change mean?
It means the gear pair is an overdrive: the output spins faster than the input, and the available torque falls.
The percentage shows how much force is given up for the extra speed, before friction losses in a real machine.
4. Does the gear ratio change the direction of rotation?
Yes, two meshing external gears always rotate in opposite directions, although the ratio figure itself stays positive.
Adding a third, idler gear restores the original direction without changing the ratio between the first and last gears.
5. Can I use the calculator for bicycle gears?
Yes. Enter the chainring teeth as the driving gear and the rear cog teeth as the driven gear, with your pedalling cadence as the input RPM.
The output RPM is then the rear wheel speed in revolutions per minute, ready to combine with wheel size for road speed.
6. What is the difference between reduction and overdrive?
A reduction has a ratio above 1 : 1 and trades speed for torque. An overdrive has a ratio below 1 : 1 and trades torque for speed.
Reductions suit lifting and starting heavy loads. Overdrives suit fans, spindles and cruising gears where speed matters more than force.
7. Why does torque rise when speed falls?
Power is speed multiplied by torque, and gears cannot create power. Halving the speed therefore doubles the ideal torque.
Friction takes a small share in real machinery, so treat the percentage shown as the ideal figure rather than a guaranteed measurement.
8. What inputs does the Gear Ratios Calculator need?
It needs exactly three values: the driving gear teeth, the driven gear teeth and the input speed in RPM.
Enter each one as labelled, then press Calculate. Every value must be greater than zero for the ratio to make physical sense.
9. What are the three results of the Gear Ratios Calculator?
The results are the gear ratio, the output speed in RPM and the torque change as a percentage.
Read together, they describe the complete trade the gear pair makes: how the turns compare, how fast the output spins and what happens to force.
10. Can I calculate a multi-stage gearbox?
Yes, one stage at a time. Calculate the first pair, then use its output speed as the input for the second pair.
The overall ratio is the two stage ratios multiplied together, and the final output speed follows from that combined figure.
11. Does gear size in millimetres matter?
Only through the tooth count. Meshing gears share the same tooth size, so counts are exactly proportional to diameters.
Counting teeth is more accurate than measuring a worn gear, which is why the tool asks for counts rather than dimensions.
12. What if both gears have the same teeth?
The ratio is 1.00 : 1, the output speed equals the input speed and the torque change is zero percent.
Such a pair is still useful for reversing direction or moving a shaft, but it changes neither speed nor force.
13. How accurate is the Gear Ratios Calculator?
The arithmetic is exact for ideal gears, because the speed relationship is a pure proportion of tooth counts.
Real machines lose a little torque to friction, so expect the delivered torque to sit slightly below the percentage shown.
14. Why did the calculator reject my values?
The tool checks that every box holds a number greater than zero, because a gear with no teeth or a speed of zero has no ratio.
Read the message, correct the value it points to, and calculate again. The check prevents a silent wrong answer.
15. Is the Gear Ratios Calculator free to use?
Yes, the tool on this page is free, with no sign-up and no limit on how many gear pairs you test.
Bookmark the page if you compare ratios often, because the same three-input method will be waiting exactly as you left it.
CONCLUSION
The Gear Ratios Calculator does one job and does it cleanly: it takes the driving gear teeth, the driven gear teeth and the input speed, and returns the gear ratio, the output speed and the torque change in seconds, with a method open enough for anyone to check. That combination of speed and transparency is what turns a number on a screen into a decision you can stand behind.
Use it whenever you choose or check a gear pair, test the reversed tooth counts as a sanity check before you commit, and remember the limits explained above. A careful input and an honest reading of all three results will serve you far better than any single figure, however precisely it is printed.