Synology Storage Calculator
People regularly feel short changed when a new NAS shows far less space than the drives promised, and some even return perfectly good hardware. Knowing the three figures in advance sets honest expectations, lets you size the drives for the displayed capacity you actually want, and helps you compare quotes and models on the same basis instead of comparing raw marketing numbers against real usable space.
Beginners often worry that they need advanced knowledge before a tool like this becomes useful, but the opposite is true. The method behind the result is fixed and well established, and the tool simply applies it carefully on your behalf. Your only job is to supply honest, up to date figures, and the more familiar you become with what each input means, the more confident your decisions will feel.
The Synology Storage Calculator on this page does the working out for you in seconds. Enter three figures, press one button, and read three clear results, with no sums to do by hand and no room for the small slips that spoil manual calculations.
What Is a Synology Storage Calculator?
Storage figures for a Synology NAS come in three flavours that are easy to confuse: the raw capacity of all the drives added together, the usable capacity left after RAID protection takes its share, and the capacity the NAS interface actually displays. That displayed figure looks smaller still, because the system counts in binary units. Understanding all three numbers explains why a shelf of large drives becomes a noticeably smaller pool on screen.
Getting this figure right matters because small mistakes at the planning stage tend to grow into bigger problems later, whether that means overspending, running short, or discovering too late that an early assumption was wrong. A dedicated tool removes the guesswork, applies the same method every single time, and lets you test several different scenarios in a few seconds before you commit money, time, or effort to any one of them.
How the Synology Storage Calculator Works
Raw capacity is the number of drives multiplied by the size of each drive, measured in terabytes as drive makers define them. Usable capacity then depends on the RAID level: RAID 0 keeps everything, RAID 1 keeps one drive’s worth, RAID 5 keeps all but one drive, RAID 6 keeps all but two, and RAID 10 keeps half. Finally, multiply usable terabytes by about 0.9095 to convert them into the tebibytes the interface displays.
The real value of a quick calculation is comparison. When you can change one number and immediately see the effect, you stop guessing which option suits you and start choosing with evidence. Run the same situation through two or three sensible variations, note how the results move, and you will usually find that one option stands out clearly as the better fit for your budget, your space, or your long term plans.
Why Use a Synology Storage Calculator?
The most common mistake is planning around the raw total and forgetting both deductions: the RAID protection share and the terabyte to tebibyte conversion. Together they can remove a third or more of the headline figure. Another frequent error is comparing one product’s raw capacity with another product’s usable capacity, which makes the honest specification look worse when it is simply measured differently.
Always pause for a quick sense check before you act on any result. Ask whether the answer looks reasonable for the figures you entered, and whether you may have typed a number into the wrong box or used the wrong unit. Most wrong answers in everyday calculations come from simple entry slips rather than from the method itself, so a ten second review of your inputs protects everything that follows from them.
Key Inputs and Outputs Explained
The Synology Storage Calculator keeps things deliberately simple, with three inputs to supply and three results to read. Understanding what each one means is the difference between a number you merely have and a number you can trust and act on with confidence.
Number of Drives: Enter this figure as accurately as you can, because every result is built on it and a small slip here moves all three answers.
Size of Each Drive (TB): Use your best current figure for this input rather than a rough guess, and update it whenever the real situation changes.
RAID Level: This input sets the scale of the whole calculation, so measure or check it carefully before you press the Calculate button.
Total Raw Capacity: This is one of the three headline answers, worked out instantly from your figures every time you calculate.
Usable Capacity (TB): Use this figure together with the other two results, because the three answers are designed to be read as a set.
Usable Capacity (TiB): This result is the one most people act on first, so sense check it against your expectations before you rely on it.
How to Use the Synology Storage Calculator
Using the Synology Storage Calculator takes less than a minute from start to finish. Gather your three figures first, then follow these steps in order.
- Enter the number of drives in the box provided.
- Enter the size of each drive (tb) in the box provided.
- Enter the raid level in the box provided.
- Check the three figures once for typing slips, because the results can only be as good as the inputs.
- Press the Calculate button and wait a moment while the results appear below.
- Read the total raw capacity, the usable capacity (tb), and the usable capacity (tib), and note them down if you plan to compare scenarios.
If a figure fails validation, a message explains what needs fixing, and nothing is calculated until every input makes sense. To start again from scratch, press the Reset button beside Calculate.
Worked Example 1: Four 4 TB Drives in RAID 5
A buyer plans four 4 TB drives in RAID 5 and wants to know what the NAS will actually display before committing to the purchase.
Step 1: Enter 4 as the number of drives.
Step 2: Enter 4 as the size of each drive (tb).
Step 3: Enter RAID 5 as the raid level.
Step 4: Press the Calculate button.
Step 5: The raw capacity is 4 times 4 TB, which equals 16 TB. RAID 5 reserves one drive, leaving 12 TB usable, and 12 times 0.9095 equals about 10.91 TiB.
Result: The NAS will show about 10.91 TiB of usable space, noticeably less than the 16 TB headline figure on the drive boxes.
Worked Example 2: Eight 6 TB Drives in RAID 6
A larger installation uses eight 6 TB drives in RAID 6, and the owner wants the raw, usable, and displayed figures side by side.
Step 1: Enter 8 as the number of drives.
Step 2: Enter 6 as the size of each drive (tb).
Step 3: Enter RAID 6 as the raid level.
Step 4: Press the Calculate button.
Step 5: The raw capacity is 8 times 6 TB, which equals 48 TB. RAID 6 reserves two drives, leaving 36 TB usable, and 36 times 0.9095 equals about 32.74 TiB.
Result: The pool provides 36 TB of usable capacity, which the interface displays as about 32.74 TiB with two drives devoted to protection.
Why Drive Makers and Computers Count Differently
Drive packaging uses decimal units, where a terabyte is 1,000 gigabytes, following the same pattern as kilometres and kilograms. Operating systems traditionally count in binary units, where a tebibyte is 1,024 gibibytes. The drives hold exactly the amount promised; the two counting systems simply slice the same capacity differently. The gap grows with size, which is why it is barely noticed on small drives and impossible to miss on large ones.
It also helps to keep a short note of the figures you used and the result you got. Circumstances change, prices move, and measurements get revised, and having last time’s numbers on hand makes the next calculation faster and far more honest. You can see at a glance what has changed, what has stayed the same, and whether your original plan still holds up or needs a fresh look.
Choosing Drives for the Capacity You Will See
Work backwards from the displayed capacity you want. If the goal is a pool that shows about 10 TiB after RAID 5 protection, the usable terabytes must be roughly 11 TB before conversion, which shapes the drive size and count you choose. Planning in the displayed unit from the start removes the disappointment of a pool that looked generous on paper and ordinary on screen.
Recalculate whenever something material changes rather than relying on an old result. A figure that was accurate last month can quietly become misleading after a price rise, a change of plan, or a new measurement. Because the calculation takes only seconds, there is no real cost to refreshing it, and the small habit of checking again is what keeps a good plan from drifting off course.
How RAID Choice Changes the Final Figure
Every protection decision is paid for in displayed capacity. RAID 6 on a large pool can set aside two whole drives plus the conversion difference, while RAID 0 shows the largest possible figure with no safety net at all. Neither is automatically right: the correct choice weighs the displayed space you gain against the rebuild risk you accept, for the specific data the pool will hold.
The real value of a quick calculation is comparison. When you can change one number and immediately see the effect, you stop guessing which option suits you and start choosing with evidence. Run the same situation through two or three sensible variations, note how the results move, and you will usually find that one option stands out clearly as the better fit for your budget, your space, or your long term plans.
Tips for Getting the Best From the Synology Storage Calculator
- 1. Plan in the displayed unit — decide how much space you want the NAS to show, then work backwards through the conversion and the RAID share to find the drives required.
- 2. Expect about nine percent conversion loss — usable terabytes shrink by roughly nine percent when displayed as tebibytes, so allow for it in every plan.
- 3. Add the RAID share on top — remember that protection is deducted before the conversion, so the two effects combine rather than overlap.
- 4. Compare like with like — when comparing models or quotes, always compare usable displayed capacity, never one raw figure against another usable figure.
- 5. Size drives for the final number — choose drive sizes using the final displayed capacity as the target, not the raw total on the boxes.
- 6. Keep some displayed headroom — a pool that shows nearly full behaves worse than the percentage suggests, so leave displayed space in reserve.
- 7. Note all three figures — write down raw, usable, and displayed capacities for your plan so future upgrades can be compared honestly.
- 8. Do not return healthy drives — a smaller displayed figure is normal counting, not a faulty drive, so check the conversion before suspecting hardware problems.
Frequently Asked Questions About the Synology Storage Calculator
1. What is a Synology Storage Calculator?
Storage figures for a Synology NAS come in three flavours that are easy to confuse: the raw capacity of all the drives added together, the usable capacity left after RAID protection takes its share, and the capacity the NAS interface actually displays. This page provides a free tool that applies the standard method for you, so you only need to supply your own figures.
If your result looks surprising, check each input once more and run the calculation again with the corrected figure.
2. How does the Synology Storage Calculator work?
Raw capacity is the number of drives multiplied by the size of each drive, measured in terabytes as drive makers define them. The tool performs each step of that method in order as soon as you press Calculate.
When in doubt, try a second set of figures as well, because comparing two scenarios usually makes the right choice obvious.
3. What information do I need to use the Synology Storage Calculator?
You need three figures: the number of drives, the size of each drive (tb), and the raid level. Nothing else is required, and there are no accounts to create or forms to save before you can see a result.
Keep a note of the figures you used, so you can repeat the same calculation later and see exactly what has changed.
4. What results does the Synology Storage Calculator show?
It shows three results together: the total raw capacity, the usable capacity (tb), and the usable capacity (tib). Reading them together gives the full picture rather than a single figure taken out of context.
A quick sense check helps here: if the answer feels far too large or far too small, an input was probably typed incorrectly.
5. How accurate is the Synology Storage Calculator?
The method it applies is the standard one for this calculation, and the arithmetic is exact, so accuracy depends almost entirely on the figures you enter. Careful, current inputs give results you can plan around with confidence.
If your result looks surprising, check each input once more and run the calculation again with the corrected figure.
6. Is the Synology Storage Calculator free to use?
Yes, it is completely free, with no sign up, no download, and no limit on how many times you can run a calculation. You can test as many different scenarios as you like until one of them fits your plans.
When in doubt, try a second set of figures as well, because comparing two scenarios usually makes the right choice obvious.
7. Can I use the Synology Storage Calculator on my phone?
Yes, the tool works in the browser on phones, tablets, and computers, and the layout adjusts to smaller screens. That makes it easy to check a figure while you are out shopping, travelling, or standing in front of the thing you are measuring.
Keep a note of the figures you used, so you can repeat the same calculation later and see exactly what has changed.
8. What is the most common mistake people make with a Synology Storage Calculator?
The most common mistake is planning around the raw total and forgetting both deductions: the RAID protection share and the terabyte to tebibyte conversion. Taking a few seconds to review your inputs before calculating avoids nearly all of these problems.
A quick sense check helps here: if the answer feels far too large or far too small, an input was probably typed incorrectly.
9. When should I run the Synology Storage Calculator again?
Run it again whenever one of your figures changes in a way that matters, such as a new price, a new measurement, or a change of plan. Because the calculation takes seconds, refreshing the result is always cheaper than acting on an out of date one.
If your result looks surprising, check each input once more and run the calculation again with the corrected figure.
10. Does the Synology Storage Calculator store the figures I enter?
No, the calculation happens entirely on this page in your browser, and the figures you enter are not sent anywhere or saved for later. If you want a record of a result, note the numbers down yourself before you leave the page.
When in doubt, try a second set of figures as well, because comparing two scenarios usually makes the right choice obvious.
11. Why does my 4 TB drive show as about 3.64 in the NAS?
Because 4 terabytes convert to about 3.64 tebibytes when multiplied by 0.9095, and the interface displays the binary unit.
The drive is holding exactly what it promised; only the counting unit has changed.
12. What is the difference between TB and TiB?
A terabyte is 1,000 to the power of four bytes in decimal counting, while a tebibyte is 1,024 to the power of four in binary counting.
The tebibyte is about ten percent larger as a unit, so the same capacity produces a smaller number in TiB.
13. Does the conversion affect how much I can store?
No, your files occupy the same physical space either way; only the number used to describe the capacity changes.
What does reduce real storage is the RAID protection share, which is a separate deduction.
14. How do I get a pool that displays 20 TiB in RAID 5?
Divide 20 by 0.9095 to get about 22 TB of usable capacity needed, then add one drive for RAID 5 protection on top of the data drives.
That reverse method ensures the displayed figure, which is the one you see daily, meets your target.
15. Is the 0.9095 factor exact?
It is a rounded version of the true ratio between the two units, accurate enough for planning drive purchases and pool sizes.
Tiny differences at the second decimal place have no practical effect on which drives you should buy.
CONCLUSION
The Synology Storage Calculator turns a fiddly manual calculation into three figures you can trust in seconds. It applies the standard method every time, shows its results as a clear set, and makes it easy to compare scenarios before you commit to a decision about your Synology storage plan.
Keep your inputs honest and current, sense check every result, and recalculate whenever your situation changes. Used that way, this simple tool becomes a reliable planning companion, helping you spend wisely, prepare properly, and avoid the costly surprises that come from guessing.